General | NX-1200 | NX-1300 | |
---|---|---|---|
Pre-set Frequencies | Type 1 | 136-174 MHz | 450-520 MHz |
Type 2 | 400-470 MHz | ||
Max. Channels per Radio | 260 (64 for basic model) | ||
Number of Zones | 128 (4 for basic model) | ||
Max. Channels per Zone | 250 (16 for basic model) | ||
Channel Spacing | Analog | 30*1 / 25*1 / 15 / 12.5 kHz | |
Digital | 12.5 / 6.25 kHz | ||
Power Supply | 7.5 VDC ±20 % | ||
Battery Life | DMR | Analog/NXDN | |
KNB-84L (1900mAh) | Approx. 14.5 hours | Approx. 11 hours | |
KNB-69L (2550mAh) | Approx. 19 hours | Approx. 14 hours | |
Operating Temperature(Radio only)*2 | -30°C to +60°C | ||
Frequency Stability (-30 to +60°C; +25°C Ref.) | ±0.5 ppm | ||
Antenna Impedance | 50 Ω | ||
Dimensions | (W x H x D) Projections Not Included | ||
Radio with KNB-84L | 54 x 123 x 33.5 mm | ||
Weight Radio Only | 175 g | ||
Radio with KNB-84L | 295 g | ||
FCC ID | Type 1 | K44501000 | K44501101 (pending) |
Type 2 | K44501100 | ||
IC Certification | 282F-501000 | 282F-501100 | |
Receiver | NX-1200 | NX-1300 | |
Sensitivity | NXDN® @ 6.25 kHz Digital (3% BER) | 0.18 μV | |
NXDN® @ 12.5 kHz Digital (3% BER) | 0.22 µV | ||
DMR® @ 12.5 kHz Digital (1% BER) | 0.25 µV | ||
DMR® @ 12.5 kHz Digital (5% BER) | 0.18 µV | ||
Analog @ 12.5/25 kHz (12 dB SINAD) | 0.24 µV / 0.20 µV | ||
Selectivity | Analog @ 12.5 / 25 kHz | 68 dB / 74 dB | |
Intermodulation Distortion | 70 dB | ||
Spurious Rejection | 70 dB | ||
Audio Distortion | 7% | ||
Audio Output Power | 1 W / 12 Ω (Internal Output) | ||
Transmitter | NX-1200 | NX-1300 | |
RF Power Output | (High / Low) | 5 W / 4 W / 1 W | |
Spurious Emission | -70 dB | ||
FM Hum & Noise | Analog @ 12.5 / 25 kHz | 40 dB / 45 dB | |
Audio Distortion | 2% | ||
DMR Digital Protocol | ETSI TS 102 361-1, -2, -3 | ||
Emission Designator | 16K0F3E, 11K0F3E, 8K30F1E, 8K30F1D, 8K30F7W, 4K00F1E, 4K00F1D, 4K00F7W, 4K00F2D, 7K60FXD, 7K60F7W |
*1 25 / 30 kHz in VHF/UHF Bands excluding T-Band are not included in the models sold in the USA or US territories.
*2 Operating temperature specification for a Li-ion battery is -10°C to +60°C [14°F to +140°F].Analog measurements made per TIA603. Specifications are measured according to applicable standards.Specifications are subject change without notice, due to advancements in technology.
FleetSync® is a registered trademark of JVCKENWOOD Corporation in the United States and/or other countries.NXDN® is a trademark of JVCKENWOOD Corporation and Icom Inc.NEXEDGE® is a registered trademark of JVCKENWOOD Corporation.All other trademarks are the property of their respective holders.
MIL Standard | MIL 810C Methods/Procedures | MIL 810D Methods/Procedures | MIL 810E Methods/Procedures | MIL 810F Methods/Procedures | MIL 810G Methods/Procedures |
---|---|---|---|---|---|
Low Pressure | 500.1/Procedure I | 500.2/Procedure I, II | 500.3/Procedure I, II | 500.4/Procedure I, II | 500.5/Procedure I, II |
High Temperature | 501.1/Procedure I, II | 501.2/Procedure I, II | 501.3/Procedure I, II | 501.4/Procedure I, II | 501.5/Procedure I, II |
Low Temperature | 502.1/Procedure I | 502.2/Procedure I, II | 502.3/Procedure I, II | 502.4/Procedure I, II | 502.5/Procedure I, II |
Temperature Shock | 503.1/Procedure I | 503.2/Procedure I | 503.3/Procedure I | 503.4/Procedure I, II | 503.5/Procedure I |
Solar Radiation | 505.1/Procedure | 505.2/Procedure I | 505.3/Procedure I | 505.4/Procedure I | 505.5/Procedure I |
Rain* | 506.1/Procedure I, II | 506.2/Procedure I, II | 506.3/Procedure I, II | 506.4/Procedure I, III | 506.5/Procedure I, III |
Humidity | 507.1/Procedure I, II | 507.2/Procedure II, III | 507.3/Procedure II, III | 507.4 | 507.5/Prcedure II |
Salt Fog | 509.1/Procedure I | 509.2/Procedure I | 509.3/Procedure I | 509.4 | 509.5 |
Dust | 510.1/Procedure I | 510.2/Procedure I | 510.3/Procedure I | 510.4/Procedure I, III | 510.5/Procedure I |
Vibration | 514.2/Procedure VIII, X | 514.3/Procedure I | 514.4/Procedure I | 514.5/Procedure I | 514.6/Procedure I |
Shock | 516.2/Procedure I, II, V | 516.3/Procedure I, IV | 516.4/Procedure I, IV | 516.5/Procedure I, IV | 516.6/Procedure I, IV |
International Protection Standard | |||||
Dust & Water Protection* | IP67 | All interfaces must be fully sealed with appropriate covers or by designated genuine accessories. Water & Dust tighten IP67 models equipped with designated genuine batteries are [M] and [X] types only. (for Asia/Oceania) |