TH-F6A / TH-F7A / TH-F7E
Memory Control
Program
MCP-F6/F7 Version 1.01 |
Last updated : November 15, 2013 |
|
|
|
| Welcome |
| Thank you for choosing the KENWOOD transceivers. By utilizing this software,
you can enjoy the versatility of the KENWOOD transceivers through the memory
channel management or edit functions. |
| |
| About this software |
 |
You can use the MCP-F6/F7 to create data such as memory channels and menus
on a PC by connecting the TH-F6A/F7A/F7E to the PC by using an optional
Programming Cable PG-4Y (RS-232 interface) or KPG-22U (USB 2.0 interface). |
|
| |
| Operating Environments |
| 1. |
Operating System (OS) |
| |
Windows® XP (Service Pack 3 or later) (32-bit)
Windows
Vista® (Service Pack 2 or later)(32-bit or
64-bit)
Windows® 7 (RTM or later) (32-bit or 64-bit)
Windows® 8 (RTM or later) (32-bit or 64-bit)
Windows® 8.1 (RTM or later) (32-bit or 64-bit) |
| |
Note:
|
This software is designed to run on the above operating systems. |
|
This software also runs on Windows® 10 and Windows® 11. (Noted on June 23, 2022) |
|
Applicable operating systems are subject to change without notice due to the
end of the technical support by Microsoft Corporation or change of the product
specifications. |
|
| 2. |
Processor |
| |
Faster than the recommended CPU for each OS. |
| 3. |
System Memory (RAM) |
| |
Larger than the recommended System Memory for each OS. |
| 4. |
Free Hard Drive Space |
| |
2MB or more of free hard drive space. |
| 5. |
Peripheral Devices |
| |
 |
A display with resolutions higher than XGA (1024 x 768). |
|
A keyboard and a mouse, or other pointing devices. |
|
An RS-232C interface (corresponding to COM1 to COM20), or a USB 2.0
interface. |
|
| 6. |
Programming Cable |
| |
|
An optional Programming Cable PG-4Y (RS-232 interface), or KPG-22U (USB 2.0
interface). |
| |
Ask your dealer about purchasing the Programming Cables. |
|
A Virtual COM port driver needs to be installed
onto the PC to use the KPG-22U programming
cable. |
|
|
| |
| Attention |
|
Turn the transceiver OFF before connecting it to a
PC. |
|
| |
| Notes on usage |
|
Users are required to obtain an approval from JVC KENWOOD Corporation, in
writing, prior to redistributing this software on a personal web page or packet
radio. |
|
Users are prohibited to assign, rent, lease, or resell the
software. |
|
Users are prohibited to revise, change, translate, merge, de-compile, or
reverse engineer the software. |
|
JVC KENWOOD Corporation does not warrant that quality and functions of this
software comply with each user's purpose of use of this software, and unless
specifically described in this document, JVC KENWOOD Corporation shall be free
from any responsibilities to any defects and indemnities to any damages or
losses. Selection and installation of this software shall be done by the user's
own designation. The user shall take full responsibility for the use and effects
of this software. |
|
JVC KENWOOD Corporation shall be free from any responsibilities for any
incidental losses or damages, such as missing communications or a call
opportunity, caused by a failure or performance error of this
software. |
|
JVC KENWOOD Corporation shall own all copyrights and other intellectual
properties for the software and all manuals and documents attached to the
software. The user shall be allowed to use, not to resell, the software by
obtaining a license from JVC KENWOOD Corporation. While the media on which the
software is stored is possessed by the user, the ownership for the software
itself shall be reserved for JVC KENWOOD
Corporation. |
|
| |
| Installing the MCP-F6/F7 |
Extract the downloaded file "MFX101.zip" into a designated folder.
In the designated folder, a folder labeled "MFX101" will be created.
Execute the "setup.exe" in the folder labeled "MFX101",
and follow the instructions that appear on the display to install MCP-F6/F7. |
Note:
|
The MCP-F6/F7 does not operate properly when selecting other models; you
must select the correct model. |
|
If you select a different model by mistake, re-install the MCP-F6/F7. |
|
Administrator privileges are required when installing the MCP-F6/F7. |
|
| |
| Uninstalling the MCP-F6/F7 |
| Select "MCP-F6/F7" in "Uninstall a program" ("Add
or Remove Programs" for Windows® XP) in the Control Panel and follow the instructions that
appear on the display to uninstall the software. Or double-click "setup.exe",
and follow the instructions that appear on the display to uninstall the
software. |
Note:
|
Created files using the MCP-F6/F7 are not deleted by uninstalling the software;
you must manually delete any files that you created. |
|
Administrative privileges are required to uninstall the MCP-F6/F7. |
|
Always exit the MCP-F6/F7 before uninstalling the software. |
|
| |
| Update History |
| Ver.1.01 (November 15, 2013) |
|
Adds Windows Vista®, Windows® 7 , Windows® 8, Windows® 8.1 compatibility. |
|
Supports COM1 through COM20. |
|
| |
| Ver.1.00 (December 10, 2002) |
|
First Release |
|
 |
|
| If you agree with the details listed above, click the following link to
download the latest MCP-F6/F7 software. |
| (The latest version includes all previous updates.) |
|
| Download MCP-F6/F7 Version 1.01 (filename: MFX101.zip; file size : 2.94MB) |
|
|
Microsoft, Windows, Windows Vista, and Windows logo are registered trademarks of Microsoft Corporation in the United States and/or other countries. |
|
